الإجابة المباشرة: An بطاقة إرسال LED sits at the signal source (PC, media player, or video processor) to encode video input into data packets over Ethernet or fiber, while an بطاقة استقبال LED is installed inside each LED cabinet to decode that data and drive the LED modules. Every synchronous LED screen needs both—and both must come from the same brand ecosystem.
Whether you are building a new LED video wall or ordering replacement spare parts, understanding how sending cards, sending boxes, and receiving cards work together prevents signal failure, color mismatch, and wasted budget.
Quick Comparison: LED Sending Card vs Receiving Card
| الميزات | LED Sending Card / Sending Box | بطاقة استقبال LED |
|---|---|---|
| دور أساسى | Captures HDMI/DVI/SDI video and transmits control signals | Receives Ethernet data and drives LED modules via HUB75/board-to-board interfaces |
| موقع التثبيت | Control room, rack, PC PCIe slot, or inside a صندوق الإرسال / video controller | Mounted directly inside every LED display cabinet |
| الكمية المطلوبة | Usually 1 unit per screen (or multiple synced units for ultra-large 4K/8K walls) | 1 card per cabinet (sometimes 1 card per 2–4 small cabinets depending on pixel load) |
| المواصفات الرئيسية التي يجب التحقق منها | Input ports (HDMI/DVI/DP/SDI), total pixel capacity, number of Ethernet/fiber outputs | Per-card pixel capacity, HUB interface type, grayscale/HDR support, RCFGX/config compatibility |
| أعراض الفشل النموذجية | Entire screen goes black or loses video input | A single cabinet (or downstream daisy-chained cabinets) goes black or shows garbled colors |
What Is an LED Sending Card?
An بطاقة إرسال LED is the bridge between your video source and the LED screen. It accepts standard video signals (HDMI, DVI, DisplayPort, or 12G-SDI), maps the resolution to your physical cabinet layout, and sends synchronized data out through Gigabit Ethernet (RJ45) or 10G optical fiber ports.

In modern installations, standalone PCIe sending cards are often replaced by external صناديق إرسال LED or all-in-one وحدات تحكم فيديو LED (مثل ال NovaPro UHD الابن or كولور لايت X40m), which integrate video scaling, multi-window switching, and sending functions in one rack-mounted chassis.
ما هي بطاقة الاستقبال المزودة بمؤشر LED؟
An بطاقة استقبال LED is installed inside each LED cabinet. It receives the digital video stream over Cat5e/Cat6 cable from the sending card (or from the previous cabinet in a daisy chain), decodes the pixel data assigned to that specific cabinet, and distributes it to the LED modules through HUB75E ribbon cables or a hard-connection backplane.

High-performance receiving cards like the نوفاستار A10s بلس also handle pixel-level brightness and chroma calibration, 18-bit+ grayscale enhancement, low-latency mode, and dual-receiver redundancy for mission-critical rental and broadcast screens.
How to Calculate How Many Sending & Receiving Cards You Need
Sizing your control system accurately requires checking three limits—never just total pixel count:
- Step 1 — Total Screen Resolution: Multiply cabinet pixel width × number of columns, and cabinet pixel height × number of rows.
- Step 2 — Receiving Card Count: Most LED cabinets use 1 receiving card per cabinet for clean wiring and easy maintenance. Verify that your chosen receiving card supports both the cabinet’s pixel area and its physical HUB interface count.
- Step 3 — Sending Card / Controller Ethernet Ports: A standard Gigabit Ethernet output typically loads up to 650,000 pixels at 8-bit 60Hz (reduced to roughly half at 10-bit/12-bit or 120Hz). Divide your total screen pixels by the per-port capacity, then round up—and always confirm the controller’s maximum horizontal width and vertical height limits.
How to Choose & Replace LED Control Cards Without Compatibility Issues

- Keep the Brand Ecosystem Identical: نوفاستار, colorlight ل, Huiduو Linsn use proprietary protocols. A sending card from one brand cannot drive receiving cards from another. (See our نوفا ستار مقابل كولورلايت مقابل Huidu دليل المقارنة.)
- Match the Exact Receiving Card Model & Firmware: When replacing a single faulty receiving card in an existing wall, match the exact model and hardware version whenever possible, and load the original configuration file (such as
.rcfgxfor NovaStar or.rcvpfor Colorlight) so brightness and color match neighboring cabinets. - Plan for Asynchronous vs Synchronous Needs: If you do not want a dedicated PC running 24/7, choose an بطاقة التحكم LED غير المتزامنة مثل Huidu HD-C16L, which combines media playback and sending functions in one unit.
Video Guide: Installing & Configuring LED Receiving Cards
Watch this step-by-step EagerLED walkthrough on installing and configuring LED receiving cards for stable display performance.
الأسئلة الأكثر شيوعًا (FAQ)
Can an LED screen work without a sending card?
Only if it uses an asynchronous media player or direct-load control card (such as certain Huidu or NovaStar Taurus models) that has built-in sending outputs. Any synchronous LED display connected to a live HDMI/DVI/SDI video source requires a sending card, sending box, or all-in-one video controller.
Can I use a newer receiving card model as a spare part in an older LED cabinet?
Sometimes, provided it is from the same brand, has a compatible HUB interface (for example, HUB75E), and is supported by your sending card’s firmware. However, you must load the matching module configuration file and check color/grayscale consistency across the screen before deploying.
What is the maximum Ethernet cable distance between a sending card and the first receiving card?
Standard Cat5e/Cat6 Ethernet cable supports up to متر 100 (80 meters recommended for stable commercial operation). For longer runs, use an optical fiber converter with single-mode or multi-mode SFP modules.
Order Genuine LED Control Cards & Spare Parts from EagerLED
تأسست في 2009، شنتشن EagerLED Co.، Ltd. is a professional LED display manufacturer offering OEM/ODM services, complete LED displays via حريصة.كوم, and genuine LED display spare parts through ledcontrollercard.comبمصنعنا الذي تزيد مساحته عن 5,000 متر مربع، وطاقتنا الإنتاجية الشهرية التي تتجاوز 6,000 متر مربع، وفريق عملنا الذي يزيد عن 150 فرداً، ومختبرنا الداخلي للاختبارات الذي تبلغ مساحته 100 متر مربع، نخضع كل وحدة LED لاختبار تقادم لمدة 24 ساعة، وكل شاشة كاملة لاختبار تقادم لمدة 72 ساعة قبل الشحن. منتجاتنا حاصلة على شهادات CE وRoHS وFCC وCB، ومصنعنا حاصل على شهادات ISO 9001 وISO 14001 وISO 45001.
يحظى بثقة العملاء في أكثر من 120 دولة، جميعها EagerLED products come with a 2-year warranty, 2% free spare parts with every order, and free remote technical support. Need help selecting compatible sending cards, receiving cards, or configuration files? اتصل بفريقنا (بريد إلكتروني: info@eagerled.com | واتساب/هاتف: +86 15361038665) — في أيام العمل، نرد على كل استفسار في غضون 12 ساعة ونرسل عرض أسعار في غضون 24 ساعة.
اشترِ شاشة LED ثابتة، انتقل إلى EagerLED.


