LED Receiving Card vs Sending Card: Differences, Compatibility & Buying Guide (2026)

پاسخ مستقیم: An کارت ارسال LED sits at the signal source (PC, media player, or video processor) to encode video input into data packets over Ethernet or fiber, while an کارت دریافت LED is installed inside each LED cabinet to decode that data and drive the LED modules. Every synchronous LED screen needs both—and both must come from the same brand ecosystem.

Whether you are building a new LED video wall or ordering replacement spare parts, understanding how sending cards, sending boxes, and receiving cards work together prevents signal failure, color mismatch, and wasted budget.

Quick Comparison: LED Sending Card vs Receiving Card

ویژگیLED Sending Card / Sending Boxکارت دریافت LED
نقش اصلیCaptures HDMI/DVI/SDI video and transmits control signalsReceives Ethernet data and drives LED modules via HUB75/board-to-board interfaces
نصب و راه اندازی محل سکونتControl room, rack, PC PCIe slot, or inside a جعبه ارسال / video controllerMounted directly inside every LED display cabinet
مقدار مورد نیازUsually 1 unit per screen (or multiple synced units for ultra-large 4K/8K walls)1 card per cabinet (sometimes 1 card per 2–4 small cabinets depending on pixel load)
مشخصات کلیدی برای بررسیInput ports (HDMI/DVI/DP/SDI), total pixel capacity, number of Ethernet/fiber outputsPer-card pixel capacity, HUB interface type, grayscale/HDR support, RCFGX/config compatibility
Typical Failure SymptomEntire screen goes black or loses video inputA single cabinet (or downstream daisy-chained cabinets) goes black or shows garbled colors

What Is an LED Sending Card?

An کارت ارسال LED is the bridge between your video source and the LED screen. It accepts standard video signals (HDMI, DVI, DisplayPort, or 12G-SDI), maps the resolution to your physical cabinet layout, and sends synchronized data out through Gigabit Ethernet (RJ45) or 10G optical fiber ports.

LED Sending Card and Video Controller Hardware
LED Sending Card & Video Controller Hardware

In modern installations, standalone PCIe sending cards are often replaced by external جعبه‌های ارسال LED or all-in-one کنترل کننده های تصویر LED (مانند NovaPro UHD Jr or Colorlight X40m), which integrate video scaling, multi-window switching, and sending functions in one rack-mounted chassis.

کارت دریافت LED چیست؟

An کارت دریافت LED is installed inside each LED cabinet. It receives the digital video stream over Cat5e/Cat6 cable from the sending card (or from the previous cabinet in a daisy chain), decodes the pixel data assigned to that specific cabinet, and distributes it to the LED modules through HUB75E ribbon cables or a hard-connection backplane.

NovaStar A10s Plus High-End LED Receiving Card
NovaStar A10s Plus High-End LED Receiving Card

High-performance receiving cards like the نوااستار A10s پلاس also handle pixel-level brightness and chroma calibration, 18-bit+ grayscale enhancement, low-latency mode, and dual-receiver redundancy for mission-critical rental and broadcast screens.

How to Calculate How Many Sending & Receiving Cards You Need

Sizing your control system accurately requires checking three limits—never just total pixel count:

  • Step 1 — Total Screen Resolution: Multiply cabinet pixel width × number of columns, and cabinet pixel height × number of rows.
  • Step 2 — Receiving Card Count: Most LED cabinets use 1 receiving card per cabinet for clean wiring and easy maintenance. Verify that your chosen receiving card supports both the cabinet’s pixel area and its physical HUB interface count.
  • Step 3 — Sending Card / Controller Ethernet Ports: A standard Gigabit Ethernet output typically loads up to 650,000 pixels at 8-bit 60Hz (reduced to roughly half at 10-bit/12-bit or 120Hz). Divide your total screen pixels by the per-port capacity, then round up—and always confirm the controller’s maximum horizontal width and vertical height limits.

How to Choose & Replace LED Control Cards Without Compatibility Issues

Matching Sending and Receiving Cards Within the Same Brand Ecosystem
Matching Sending and Receiving Cards Within the Same Brand Ecosystem

Video Guide: Installing & Configuring LED Receiving Cards

Watch this step-by-step EagerLED walkthrough on installing and configuring LED receiving cards for stable display performance.

سوالات متداول (FAQ)

Can an LED screen work without a sending card?

Only if it uses an asynchronous media player or direct-load control card (such as certain Huidu or NovaStar Taurus models) that has built-in sending outputs. Any synchronous LED display connected to a live HDMI/DVI/SDI video source requires a sending card, sending box, or all-in-one video controller.

Can I use a newer receiving card model as a spare part in an older LED cabinet?

Sometimes, provided it is from the same brand, has a compatible HUB interface (for example, HUB75E), and is supported by your sending card’s firmware. However, you must load the matching module configuration file and check color/grayscale consistency across the screen before deploying.

What is the maximum Ethernet cable distance between a sending card and the first receiving card?

Standard Cat5e/Cat6 Ethernet cable supports up to متر 100 (80 meters recommended for stable commercial operation). For longer runs, use an optical fiber converter with single-mode or multi-mode SFP modules.

Order Genuine LED Control Cards & Spare Parts from EagerLED

در 2009 تاسیس شد، شنژن EagerLED شرکت آموزشی ویبولیتین is a professional LED display manufacturer offering OEM/ODM services, complete LED displays via eagerled.com, and genuine LED display spare parts through ledcontrollercard.comبا کارخانه‌ای به مساحت بیش از ۵۰۰۰ متر مربع، ظرفیت تولید ماهانه بیش از ۶۰۰۰ متر مربع، تیمی متشکل از بیش از ۱۵۰ نفر و یک آزمایشگاه تست داخلی به مساحت ۱۰۰ متر مربع، ما هر ماژول LED را قبل از ارسال، تحت آزمایش ۲۴ ساعته فرسودگی و هر صفحه نمایش کامل را تحت آزمایش ۷۲ ساعته فرسودگی قرار می‌دهیم. محصولات ما دارای گواهینامه‌های CE، RoHS، FCC و CB هستند و کارخانه ما دارای گواهینامه‌های ISO 9001، ISO 14001 و ISO 45001 می‌باشد.

مورد اعتماد مشتریان در بیش از ۱۲۰ کشور، همه EagerLED products come with a 2-year warranty, 2% free spare parts with every order, and free remote technical support. Need help selecting compatible sending cards, receiving cards, or configuration files? با تیم ما تماس بگیرید (پست الکترونیک: info@eagerled.com | واتس‌اپ/تلفن: 86 15361038665+ ) — در روزهای کاری، ما ظرف ۱۲ ساعت به هر درخواستی پاسخ می‌دهیم و ظرف ۲۴ ساعت قیمت پیشنهادی را ارسال می‌کنیم.

خرید نمایشگر LED پایدار، به EagerLED.

ارسال نظر

سبد خرید
0
0
سبد خرید شما
سبد خرید شما خالی استبازگشت به فروشگاه
رفته به بالا