LED Receiving Card vs Sending Card: Differences, Compatibility & Buying Guide (2026)

직접 답변: An LED 보내는 카드 sits at the signal source (PC, media player, or video processor) to encode video input into data packets over Ethernet or fiber, while an LED 수신 카드 is installed inside each LED cabinet to decode that data and drive the LED modules. Every synchronous LED screen needs both—and both must come from the same brand ecosystem.

Whether you are building a new LED video wall or ordering replacement spare parts, understanding how sending cards, sending boxes, and receiving cards work together prevents signal failure, color mismatch, and wasted budget.

Quick Comparison: LED Sending Card vs Receiving Card

제품 특장점LED Sending Card / Sending BoxLED 수신 카드
주요 역할Captures HDMI/DVI/SDI video and transmits control signalsReceives Ethernet data and drives LED modules via HUB75/board-to-board interfaces
설치 위치Control room, rack, PC PCIe slot, or inside a 보내는 상자 / video controllerMounted directly inside every LED display cabinet
수량 필요Usually 1 unit per screen (or multiple synced units for ultra-large 4K/8K walls)1 card per cabinet (sometimes 1 card per 2–4 small cabinets depending on pixel load)
확인해야 할 주요 사양Input ports (HDMI/DVI/DP/SDI), total pixel capacity, number of Ethernet/fiber outputsPer-card pixel capacity, HUB interface type, grayscale/HDR support, RCFGX/config compatibility
Typical Failure SymptomEntire screen goes black or loses video inputA single cabinet (or downstream daisy-chained cabinets) goes black or shows garbled colors

What Is an LED Sending Card?

An LED 보내는 카드 is the bridge between your video source and the LED screen. It accepts standard video signals (HDMI, DVI, DisplayPort, or 12G-SDI), maps the resolution to your physical cabinet layout, and sends synchronized data out through Gigabit Ethernet (RJ45) or 10G optical fiber ports.

LED Sending Card and Video Controller Hardware
LED Sending Card & Video Controller Hardware

In modern installations, standalone PCIe sending cards are often replaced by external LED 송신 박스 or all-in-one LED 비디오 컨트롤러 (와 같은 노바프로 UHD 주니어 or 컬러라이트 X40m), which integrate video scaling, multi-window switching, and sending functions in one rack-mounted chassis.

LED 수신 카드란 무엇인가요?

An LED 수신 카드 is installed inside each LED cabinet. It receives the digital video stream over Cat5e/Cat6 cable from the sending card (or from the previous cabinet in a daisy chain), decodes the pixel data assigned to that specific cabinet, and distributes it to the LED modules through HUB75E ribbon cables or a hard-connection backplane.

NovaStar A10s Plus High-End LED Receiving Card
NovaStar A10s Plus High-End LED Receiving Card

High-performance receiving cards like the 노바스타 A10s 플러스 also handle pixel-level brightness and chroma calibration, 18-bit+ grayscale enhancement, low-latency mode, and dual-receiver redundancy for mission-critical rental and broadcast screens.

How to Calculate How Many Sending & Receiving Cards You Need

Sizing your control system accurately requires checking three limits—never just total pixel count:

  • Step 1 — Total Screen Resolution: Multiply cabinet pixel width × number of columns, and cabinet pixel height × number of rows.
  • Step 2 — Receiving Card Count: Most LED cabinets use 1 receiving card per cabinet for clean wiring and easy maintenance. Verify that your chosen receiving card supports both the cabinet’s pixel area and its physical HUB interface count.
  • Step 3 — Sending Card / Controller Ethernet Ports: A standard Gigabit Ethernet output typically loads up to 650,000 pixels at 8-bit 60Hz (reduced to roughly half at 10-bit/12-bit or 120Hz). Divide your total screen pixels by the per-port capacity, then round up—and always confirm the controller’s maximum horizontal width and vertical height limits.

How to Choose & Replace LED Control Cards Without Compatibility Issues

Matching Sending and Receiving Cards Within the Same Brand Ecosystem
Matching Sending and Receiving Cards Within the Same Brand Ecosystem
  • Keep the Brand Ecosystem Identical: 노바스타, 컬러 라이트, Huidu예산 및 Linsn use proprietary protocols. A sending card from one brand cannot drive receiving cards from another. (See our 노바스타 vs 컬러라이트 vs Huidu 비교 가이드.)
  • Match the Exact Receiving Card Model & Firmware: When replacing a single faulty receiving card in an existing wall, match the exact model and hardware version whenever possible, and load the original configuration file (such as .rcfgx for NovaStar or .rcvp for Colorlight) so brightness and color match neighboring cabinets.
  • Plan for Asynchronous vs Synchronous Needs: If you do not want a dedicated PC running 24/7, choose an 비동기 LED 제어 카드 등 등 Huidu HD-C16L, which combines media playback and sending functions in one unit.

Video Guide: Installing & Configuring LED Receiving Cards

Watch this step-by-step EagerLED walkthrough on installing and configuring LED receiving cards for stable display performance.

자주 묻는 질문 (FAQ)

Can an LED screen work without a sending card?

Only if it uses an asynchronous media player or direct-load control card (such as certain Huidu or NovaStar Taurus models) that has built-in sending outputs. Any synchronous LED display connected to a live HDMI/DVI/SDI video source requires a sending card, sending box, or all-in-one video controller.

Can I use a newer receiving card model as a spare part in an older LED cabinet?

Sometimes, provided it is from the same brand, has a compatible HUB interface (for example, HUB75E), and is supported by your sending card’s firmware. However, you must load the matching module configuration file and check color/grayscale consistency across the screen before deploying.

What is the maximum Ethernet cable distance between a sending card and the first receiving card?

Standard Cat5e/Cat6 Ethernet cable supports up to 100 미터 (80 meters recommended for stable commercial operation). For longer runs, use an optical fiber converter with single-mode or multi-mode SFP modules.

Order Genuine LED Control Cards & Spare Parts from EagerLED

2009 년에 설립 된, Shenzhen EagerLED 유한 회사, is a professional LED display manufacturer offering OEM/ODM services, complete LED displays via 열망하는 사람들.com, and genuine LED display spare parts through ledcontrollercard.com5,000m²가 넘는 공장과 월 6,000m² 이상의 생산 능력, 150명 이상의 직원, 그리고 100m² 규모의 자체 테스트 연구실을 갖춘 당사는 모든 LED 모듈에 대해 24시간 에이징 테스트를, 모든 완제품 스크린에 대해 72시간 에이징 테스트를 출하 전에 실시합니다. 당사 제품은 CE, RoHS, FCC 및 CB 인증을 획득했으며, 공장은 ISO 9001, ISO 14001 및 ISO 45001 인증을 보유하고 있습니다.

120개국 이상 고객의 신뢰를 받는 모든 EagerLED products come with a 2-year warranty, 2% free spare parts with every order, and free remote technical support. Need help selecting compatible sending cards, receiving cards, or configuration files? 자세한 내용은 저희에게 (이메일: info@eagerled.com | WhatsApp/전화: +86 15361038665평일에는 모든 문의에 12시간 이내에 답변드리고 24시간 이내에 견적서를 보내드립니다.

안정적인 LED 디스플레이를 구매하려면 다음으로 이동하세요. EagerLED.

코멘트 남김

장바구니
0
0
장바구니
장바구니가 비어 있습니다가게로 돌아 가기
위쪽으로 스크롤