YuanChi YC-200W16-5V 5V 40A Power Supply Overview
The YuanChi YC-200W16-5V converts AC power to 5V DC for compatible LED display modules and equipment. It provides 40A rated output current and 200W rated output power, with a nominal AC input of 200–240V. The manufacturer specifies a wider input range of 176–264VAC, subject to its input-voltage derating guidance.
This power supply uses dual-transistor forward control technology with input/output isolation. Its narrow 220 × 47.6 × 26 mm housing can be assessed against the available mounting space in an LED display cabinet. Compatibility depends on the module voltage, required load, terminal arrangement and installation conditions.
Technical Specifications
| Parameter | Specification |
|---|---|
| Manufacturer / model | Shenzhen YuanChi Electronics Co., Ltd. / YC-200W16-5V |
| DC output voltage | 5.0V |
| Rated output current | 40A |
| Rated output power | 200W |
| Peak output current | 45A; this is not the continuous rated current |
| Output regulation | ±5% |
| Nominal AC input | 200–240VAC |
| AC input voltage range | 176–264VAC; load derating applies at low input voltage |
| Input frequency | 47–63Hz |
| Maximum AC input current | 3.0A at full load |
| Efficiency | 88% minimum at 230VAC, full load |
| Protection | DC output overcurrent and short-circuit protection; short-circuit protection uses hiccup mode and recovers after the short is removed |
| Cooling | Natural ventilation cooling |
| Dimensions (L × W × H) | 220 × 47.6 × 26 mm |
| Weight | Approximately 350g |
| Operating temperature | −40°C to +50°C, as listed in the environmental requirements |
| Operating humidity | 10–90% RH, non-condensing |
Values above refer to the linked manufacturer specification. Use the rated 40A / 200W output for selection and follow the datasheet load curves and installation conditions. The 45A peak value is not a continuous-load rating.
Choosing a Power Supply for Your LED Display
- Match the DC voltage: confirm that the LED modules and other connected devices require 5V DC.
- Check the AC supply: the specified 176–264VAC input range does not cover 110V or 120V mains.
- Calculate the load: use the modules’ maximum power requirements and allow suitable operating headroom. Module count cannot be determined from pixel pitch alone.
- Check cabinet fit: compare the 220 × 47.6 × 26 mm dimensions, mounting drawing and terminal positions with your existing installation.
- Review operating conditions: provide ventilation and follow the input-voltage and temperature guidance in the specification.
For a replacement, compare the complete model label and wiring arrangement before ordering. Browse our LED power supplies or contact us with the existing power supply label and LED module requirements.
Frequently Asked Questions
What is the rated output of the YC-200W16-5V?
The rated output is 5V DC at 40A, with 200W rated output power. The specification also lists 45A peak current, which should not be treated as a continuous rating.
Can this power supply run on 110V or 120V AC?
No. The specified input range is 176–264VAC, with a nominal range of 200–240VAC. Choose a power supply with an appropriate input rating for 110V or 120V mains.
How many LED modules can one power supply support?
The number depends on each module’s maximum power demand and the installation conditions. Add the loads, allow operating headroom and apply the manufacturer’s derating guidance. There is no fixed module count for every LED display.
What are the dimensions of this model?
The manufacturer lists 220 mm length × 47.6 mm width × 26 mm height and an approximate weight of 350g. Check the mechanical drawing in the PDF for mounting details.
Where can I find the YC-200W16-5V datasheet?
The original manufacturer specification is available in the download section below. It includes electrical characteristics, load derating curves, protection details and a dimension drawing.
Product Photos













